Taylor Refrigerator 428 Manuale Utente

OPERATOR’SMANUALModel 428Shake/Slush FreezerOriginal Operating Instructions055058- MFebruary, 2001 (Original Publication)(Updated 8/25/14)

6Model 428Safety130415S DO NOT allow untrained personnel tooperate this machine.S DO NOT operate the freezer unless allservice panels and access doors

7Model 428 Operator Parts Identification101101Section 4 Operator Parts IdentificationModel 428Figure 1ITEM DESCRIPTION PART NO.1 LENS-LIGHT 0529522 PL

8Model 428Operator Parts Identification120614Beater Door Assembly With Standard Door (No Prime Plug)Figure 2

9Model 428 Operator Parts Identification120614Beater Door Assembly With Standard Door (No Prime Plug)ITEM DESCRIPTION PART NO.1 PIN A.-VALVE HANDLE X2

10Model 428Operator Parts Identification120614Beater Door Assembly With Self- Closing/Prime Plug DoorFigure 3

11Model 428 Operator Parts Identification120614Beater Door Assembly With Self- Closing/Prime Plug DoorITEM DESCRIPTION PART NO.1 CAP A.- SPRING - RETA

12Model 428Operator Parts Identification140718AccessoriesFigure 4ITEM DESCRIPTION PART NO.1 KIT A.-TUNE UP X504132 BRUSH-MIX PUMP BODY-3”X7” 0233163 B

13Model 428 Important: To the Operator081002Section 5 Important: To the OperatorFigure 5ITEM DESCRIPTION PART NO.1 SWITCH- ROCKER AUTO/WASH (POWER SWI

14Model 428Important: To the Operator080313Power SwitchThe center position is OFF. The right position is AUTO,which activates the beater motor and the

15Model 428 Operating ProceduresSection 6 Operating ProceduresThe Model 428 freezer is designed to produce shakeor slush product at the desired thickn

Complete this page for quick reference when service is required:Taylor Distributor:Address:Phone:Service:Parts:Date of Installation:Information found

16Model 428Operating ProceduresStep 3Insert the drive shaft into the rear shell bearing andengage the square end firmly into the female socket ofthe d

17Model 428 Operating Procedures120418Step 7Insert the torque rotor end with the guide bearing intothe pilot hole in the center of the drive shaft. Th

18Model 428Operating ProceduresStep 12With the ice buster in place, rotate the draw valve toallow installation of the draw handle. This will lock thei

19Model 428 Operating ProceduresStep B - Self- Closing Door AssemblyInsert the draw valve into the door.Figure 23Step C - Self- Closing Door AssemblyR

20Model 428Operating ProceduresStep G - Self- Closing Door AssemblyPlace the o- ring onto the prime plug and lubricate.Figure 28Step H - Self- Closing

21Model 428 Operating Procedures050415Step L - Self- Closing Door AssemblyPosition the torque arm by inserting it down into thehole on the torque roto

22Model 428Operating Procedures140718SanitizingStep 1Prepare a 2- 1/2 gallon (9.5 liter) pail ofcleaning/sanitizing solution with an active chlorineco

23Model 428 Operating Procedures050415Priming the Freezing CylinderStep 1With a pail beneath the door spout, move the drawhandle to the right. Pour tw

24Model 428Operating Procedures140718Step 5Place the mix hopper cover in position. For properoperation, there must be a substantial amount of mixin th

25Model 428 Operating Procedures080428RinsingStep 1Pour two gallons (7.6 liters) of cool, clean water into themix hopper. With the brushes provided, s

Model 428 Table of ContentsTable of ContentsSection 1 To the Installer 1...Section 2 To the Operator 4...

26Model 428Operating Procedures080313DisassemblyBE SURE THE POWER SWITCH IS INTHE OFF POSITION. Failure to follow thisinstruction may result in severe

27Model 428 Important: Operator Checklist051207Section 7 Important: Operator ChecklistDuring Cleaning and Sanitizing:ALWAYS FOLLOW LOCAL HEALTH CODESC

28Model 428Important: Operator ChecklistWinter StorageIf the place of business is to be closed during the wintermonths, it is important to protect the

29Model 428 Troubleshooting GuideSection 8 Troubleshooting GuidePROBLEM PROBABLE CAUSE REMEDY PAGEREF.1. No product beingdispensed.a. Power switch is

30Model 428Troubleshooting GuidePROBLEM PROBABLE CAUSE REMEDY PAGEREF.4. Product too thick. a. Inadequate mix in hopper. a. Fill hopper with mix. 24b.

31Model 428 Parts Replacement ScheduleSection 9 Parts Replacement SchedulePART DESCRIPTION EVERY 3MONTHSEVERY 6 MONTHS ANNUALLY QUANTITIESTO BEREPLACE

32Model 428Limited Warranty on Equipment131206Section 10 Limited Warranty on EquipmentTAYLOR COMPANY LIMITED WARRANTY ON FREEZERSTaylor Company, a div

33Model 428 Limited Warranty on Equipment3. Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual.4. External hose

34Model 428Limited Warranty on Parts131206Section 11 Limited Warranty on PartsTAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTSTaylor Company, a

35Model 428 Limited Warranty on PartsLIMITED WARRANTY EXCEPTIONSThis limited warranty does notcover:1. Labor or other costs incurred for diagnosing, r

Table of Contents Model 428Table of Contents - Page 2Section 10 Limited Warranty on Equipment 32...Section 11 Limited Warrant

36Model 428Limited Warranty on PartsLIMITATION OF WARRANTYTHIS LIMITED W ARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONSAND/OR

428062598-1211/13/13GRN/YELWHTBLKBLK BLKGROUND FRAME SECURELYMT2COMPRESSORL2L1T1COMPRESSORCONTACTORCONDENSERFAN MOTORBEATERMOTOROVERLOADSWITCHCOMPRESS

428062598-4011/13/13GRN/YELBLUBRNBLKBLK BLKGROUND FRAME SECURELYMT2COMPRESSORL2L1 T1COMPRESSORCONTACTORCONDENSERFAN MOTORBEATERMOTOROVERLOADSWITCHCOMP

1Model 428 To the Installer131206Section 1 To the InstallerThe following information has been included in themanual as safety and regulatory guideline

2Model 428To the Installer080828Electrical Conn ection sThis equipment is supplied with a 3-wire cord andgrounding type plug, for connection to a sing

3Model 428 To the Installer130923Appliances that are permanently connected tofixed wiring and for which leakage currents mayexceed 10 mA, particularly

4Model 428To the Operator131206Section 2 To the OperatorThe freezer you have purchased has been carefullyengineered and manufactured to give you depen

5Model 428 Safety130415Section 3 SafetyWe, at Taylor Company, are concerned about thesafety of the operator when he or she comes in contactwith the fr